ARS NB9M

Cleaning & Maintaining Collectible Radios


Care & Restoration 0 Comments 07/04/2017 (This is a Level 1 Resource)

Improve and stabilize your collectible without a lot of work!

Posted By: Uncle Brad (UncleBrad)

Cleaning & Maintaining Collectible Radios

If you have found a treasure in reasonably good cosmetic condition, there is process to improve and stabilize it without a lot of work.

Before you begin, ensure you have the best panels and other parts for your radios.  I use the best covers, knobs, meters and other components from donor rigs all the time.

 The fundamentals are the same as detailing automobiles; even the products used are the same.

What You Will Need

  1. Air compressor w/extended blow nozzle accessory
  2. Simple Green solution
  3. Several microfiber cloths
  4. Soft, authentic, good-quality sponge
  5. Toothbrush
  6. Hobby brushes
  7. 000 steel wool
  8. Meguiars Cleaner Wax
  9. Meguiars Quick Detailer
  10. Lemon Pledge
  11. PlastX Polishing Compound
  12. Goo Gone
  13. Machining oil
  14. DeOxit
  15. Ultrasonic Cleaner

Steps

  1. Remove the radio from the case.  Using the blow nozzle, carefully use compressed air on most surfaces.  Stay away from speakers and delicate components.  Do not spray inside IF cans.  You can destroy a speaker very quickly using compressed air!  The idea is to remove potentially abrasive dirt before washing.
  2. Prepare a bucket of soapy water.  Any dishwashing liquid will do, but Dawn works best for the greasy, oily surfaces.
  3. Pull out all the tubes and/or removable boards.
  4. Spray the Simple Green solution on the chassis, about 6" square.  Using a toothbrush and hobby brushes, clean the area.  Progress to other areas.  Wrap a microfiber towel around the handle of your toothbrush and dry the areas as you clean them, carefully working around IF cans, variable caps, etc.
  5. On corroded chassis areas, such as the exposed metal backside, use 000 steel wool with a little machining oil and gently rub out if possible, using a circular motion.
  6. Use de-oxit on the tube sockets, wafer switches, slide and potentiometers.
  7. If the knobs are dirty, remove them and place in an ultrasonic cleaner for about 45 minutes with water and a bit of dishwashing soap. 
  8. Clean the line cord with the Simple Green solution and working it through a microfiber cloth.
  9. Using a soft, authentic, good-quality sponge, liberally apply the soapy water on the front panel and scrub with the soft sponge.  In very dirty areas, gently use a toothbrush.  Avoid getting water in meter movements.  Allow to dry in the open sun.
  10. Use Goo Gone and your fingernail for any old, dried adhesives found.  You will NOT scratch or damage the surface as long as you use your fingernail and invest some time.
  11. If the front panel surface is faded, and the paint is not chalky or damaged, test a small portion with cleaner wax to see if the surface shines up.  If so, carefully use cleaner wax. Skip this step if the front panel is in good shape.
  12. If the knobs are off, put them back on the radio.  You can use the toothbrush to clean the indicator markings.
  13. Spray about a 6" square portion of the front panel with  Meguiars Quick Detailer.  Do not substitute with another brand!
  14. Using a dry, clean microfiber cloth, quickly and gently buff the area.  This product can be used on any surface; no need to avoid plastics.  In fact, the knobs will shine up nicely with Quick Detailer.  Move on to other areas with the Quick Detailer until the front panel is finished.
  15. Lubricate any bearings with the machining oil.
  16. Reassemble the radio.
  17. Polish the case with Lemon Pledge and a microfiber cloth.  Lemon Pledge works on ANYTHING - metal, plastic, or wood.  It will help protect even the chassis.
  18. Remove and polish meter plastic covers with PlastX if necessary, using the instructions provided on the bottle.  Re-install.


Description Comment  
Process in the MS Word Format (.docx format)

   For over nearly five years, spanning 1978 - 1983 I worked as an Electronics Technician and the original Bearcat manufacturing and service facility in Cumberland, Indiana.  Electra was one of the best places I've ever worked, and were among the many innovative consumer electronics companies which sprang up in and around Indianapolis.  Al Lovell, a former employee of Regency (also in I...  READ MORE
- Uncle Brad (UncleBrad),  02/22/2018 
   The tube-type Linear Master Oscillators (“LMO”) used in the Heathkit SB-Line equipment is a very stable and accurate means of controlling the frequency in the equipment. Unfortunately, as the units age, many LMOs develop a “warble” when tuning. This “warble” usually stops when the frequency control knob is not rotated. However, accurately “zero-beating&rdq...  READ MORE
- Uncle Brad (UncleBrad),  02/08/2018 
  

NB9M Studio C Installed

A creative solution to managing big boxes in limited space.
Category: The Radio Shack
(Shown: 1/7/2018 checkin with the DX-60 Net on 3880, using the DX-60/HG-10B/HO-10 and the RME-6900)Using furniture-grade 5/8" plywood, simple tools and cold garage during Christmas vacation, I constructed Studio C, which occupies the south wall of the shack.  Exploiting a sturdy, existing cabinet with drawers that I've had since I was a kid, I devised a scheme to reliably handle the ...  READ MORE
- Uncle Brad (UncleBrad),  01/07/2018 
  

Remembering Fielden Farrington

CBS announcer, writer, author and announcer
Category: OTR
Remembering Fielden FarringtonAuthor, announcer and long-time CBS writer Fielden Ward Farrington was born July 4, 1909 in Clinton, Indiana.  He was my great-uncle; the younger brother of my grandmother, Thelma (Farrington) Stone.  Two weeks prior to his birth, his older brother Leo passed away with scarlet fever.  His father Harry, a talented carpenter, built the house in which...  READ MORE
- Uncle Brad (UncleBrad),  12/16/2017 
  

Super Hoosier DynaLoop

Construction and Description of a 160M loop antenna
Category: The Radio Shack
The Super Hoosier DynaLoop consists of four 35ft (average) utility poles buried an average of 5ft, 125ft LMR-400 from R&L Electronics, a 5KW-rated 4-1 balun, rope and marine-grade hardware (mostly from EBay) and a 20ft length of 300ohm ladder line..  The closest pole is nearly 100ft away from the shack.  The poles are 140ft apart.  The antenna is far away from any powe...  READ MORE
- Uncle Brad (UncleBrad),  11/25/2017 
   The hamshack is the result of a lot of thought. Featuring four 120V circuits on 200A service, as well as a 240V circuit for the amps, the idea was to have at hand dedicated equipment per band.  About 12 'X 18', carefull planning allows for sufficient room to both work and play.The shack is air conditioned and heated, with numerous switched antenna options for HF/VHF and UHF. &nbs...  READ MORE
- Uncle Brad (UncleBrad),  08/04/2017 
   I picked these up at the 2107 Sturgis, MI AM Swapmeet, amidst a pack curious OMs.  What a find!  Jerry replaced the original transformer in the linear power supply with a new AL-811H transformer.  The cosmetic condition of these relatively hard-to-find Gonsets is astonishing.  There is one front panel scuff on the GSB-101, and a few inperfections in the cases (original pai...  READ MORE
- Uncle Brad (UncleBrad),  07/30/2017 
  

W9DYV Jonesborough, TN 2017 Event

Pictures of forums, swapmeet and other activities
Category: Activities
Here are some pictures from the 5th annual event at the estate of W9DYV, Wes Schum.  This is truly becoming THE place to be for serious vintage communications enthusiasts.  Thanks to Nick Tusa, K5EF and all the others involved in the forums and hands-on workshops.for their participation, and also to John and Diane Voght, our hosts in the beautiful Storybrook Farm Bed & Breakfast. &nb...  READ MORE
- Uncle Brad (UncleBrad),  07/30/2017 

VIEW News Item

Brother Stair Back on the Air Soon?

Released on January 24 with a $750,000 bail
VIEW News Item

Check Out the National NC-183D!

Thanks to Jerry, K9GAS, for this superb example.
VIEW News Item

Philo T. Farnsworth Fiasco

Forgotten Relics of Inventor of Electronic TV
VIEW News Item

What Was Your First Rig?

Another N6TLU Question of the Day, 2017 AM Get Together, Sturgis MI
VIEW News Item

W8TOW Resurrects a BC779 SuperPro

Steve releases YouTube videos on operation & alignment
VIEW News Item

W9DYV Presentation Videos - Jonesborough, TN 2016

The presentations of Bob Heil, Mike Bohn, Bob Nickels and others now on YouTube!
VIEW News Item

2018 Novice Rig Roundup

March 3, 2018 - March 11, 2018

(There are currently no Blogs.)